SEAL Image 600-C Instrucciones de operaciones

SealImage 60 CImage 60 SOwners Manual

10Safety FeaturesEmergency stop buttonsThere are two Emergency Stop buttons and they are located on top of the right and left cabinets ofthe laminator

11Safety FeaturesThe forward rotation of the rollers will stop when: The opto-electronic protective device in front of the main rollers is interrupt

12General InformationWorking Space24 inch /600 mmmaximum boardlengthmaximum boardlengthroom width = 15 feet / 4.5 meter62 inch /1575 mmroll oflaminate

13General Information Power Sources – Only connect the laminator to the power supply specified on theidentification label. Refer to the “Specificatio

14Technical SpecificationMaximum working width: 62 inches 1575 mmMaximum roller width: 66 inches 1675 mmMaximum roller nip opening: 1 3/16 inches 30 m

15Un-crating and Moving The Image 60C/SYour Image 60C/S laminator is supplied in its own custom designed box with integral 4-way entrypallet and its w

16Operating ConditionsTemperature10 0C - 50 0C (50 0F - 122 0F)Do not expose the laminator to direct sunlight as output quality may be affected.Moistu

17Main SwitchThe main electrical supply “ON/OFF” switch is located on the backside of the right cabinet.The rocker switch of the IMAGE 60C has two pos

18Control Panel11 1 2 3 6 4 5 7 8 9101213141516Control panel Image 60 C

19Control PanelControl panel 60 CNo. Action or Indication1. This LED indicates that the setting of the nip opening is showed in mm (SI Unit).2. This

2ContentsSubject PageContentsIllustrationsLimited Warranty on Seal Image LaminatorsIntroductionUsing this manualFeatures and benefits of the Image 60C

20Control Panel11 1 2 3 6 4 5 7 8 91012131415162423222120252627282930Control panel Image 60 S

21Control PanelControl panel 60 SNo. Action or Indication20. This LED indicates that the set-point of the roller temperature is showed in 0C (degrees

22Control PanelThe laminators control panel is situated on the front right.The control panel of the 60C is divided into 2 sections, motor control sect

23Control PanelFoot pedalThe foot pedal is connected by cable to the machine and has to be positioned at the floor in front ofthe laminator.The foot p

24Control PanelDISPLAY SECTIONLeft display shows roller nip setting or motor current.When roller rotation mode is not active: the roller nip setting

25Emergency Stop ButtonsEmergency stop buttonsThere are two buttons and they are located on top of the right and left cabinets of the laminator.They s

26Roller up/down and roller pressureRoller up/downRotation of the hand wheel clockwise will move the roller down, the value of the nip setting (theth

27Roller up/down and roller pressureSetting pre-pressure and nip opening when processing panelsExample: Mounting print at recommended pre-pressure of

28Supply shaftsUnwind brakeUnwind brake tension settingRotation of the knob clockwise will increase the unwind brake tension.Rotation of the knob coun

29Supply shaftsLoading rollsThe machine has 2 pivoting, cantilevered supply shafts with integrated unwind brake for easyloading and webbing. One suppl

3IllustrationsSubject PageFeatures and benefits of the Image 60C/SWorking spaceIdentificationWood blocksMain switchControl panel Image 60CControl pane

30Feed-in tableThe machine has:•••• A Swinging feed-in table for easy loading, with integrated Emergency Stop System.•••• An Image guide to help feed-

31Front take-up shaft•••• Front take-up shaft for winding-up the release liner of some laminates and adhesives.The take-up shafts have integrated wind

32Laminating and Adhesive Coating (Decaling)This process involves sandwiching an image between either a hot or cold laminate on the face ofthe image a

33Laminating and Adhesive Coating (Decaling)PreparationSelect the films that you will use on the top and bottom of the images, it is advisable to use

34MountingThis process involves mounting down previously made decals onto a substrate. No films oradhesives are used in this process.To mount decals o

35MountingStep 8 – Remove the image from the rear of the laminator and trim if necessary.If the board is accidentally sent in too far at first, the re

36Cleaning & MaintenanceCleaningRemove the electrical power before commencing any maintenance on thelaminator.Do not use an abrasive cleaner on an

37Cleaning & MaintenanceMaintenanceRemove of right cover1. Remove the hand wheel for roller up/down. Press the central plastic cap at one end to

38Cleaning & MaintenanceLubrication1. The roller up/down screw threads at right and left side should be lubricated twice a year. Use aacid-free V

39TroubleshootingProblem: The laminator has no display Solution 1: Ensure that the mains supply to the laminator is O.K. Solution 2: Unplug the lami

4Limited Warranty on Seal Image LaminatorsSeal Graphics warrant to the original consumer purchaser that all new Seal Image Laminators thatprove defect

40Glossary of Laminating TermsEncapsulating – Sandwiching an image between two heat activated films.Film – A synonym for laminate. The clear material

41AccessoriesThe following accessories are supplied with the laminator:User manualOpen ended spanner 19 mm (2x)Open ended spanner 17 mm (1x)Spare fuse

42Conversion listConversion listmm >> decimal inchinch >> mmmm inch dec inch mm1 1.00 25.40025 0.9820 0.793/4 0.75 19.0505/8 0.63 15.8751

43Conversion listConversion listRoller line Roller line Roller line Roller lineForce force force forceN/mm kg/cm Lbs/inch Lbs/cm0.60 0.60 3.42 1.350.6

44Conversion listConversion listFahrenheit > CelsiusCelsius > FahrenheitAbsolute F C C F1 5010 20682 6016 25773 7021 30864 8027 35955 90 32 40 1

46

5IntroductionThank you for purchasing the IMAGE 60C/S laminator. It has been designed to give you years ofreliable service. The IMAGE 60C/S brings a n

6Features and Benefits of the Image 60C/S12345678 91011

7Features and Benefits of the Image 60C/SImage 60C:1. Digital touch pad control-panel with LED indicators and preset settings for, 60C: speed, nip-op

8

9Safety InformationThe IMAGE 60C/S laminator is provided with safety equipment to promote safe machine operation.You should however take note of the f